Winkelmandje tonen (0 Artikel) Uw accountVerlanglijstje tonenNaar de kassa

EA 40 Epoxy Glue

EA-40® Clear Amber Epoxy is an unfilled low-viscosity epoxy adhesive that can be spread easily in thin films that are almost transparent after curing. EA-40® has a long pot life and cures in 24 hours at room temperature to provide good mechanical and electrical properties. Mix ratio is 1:1 by volume. When mixed 2A:1B by volume, EA-40® will achieve greater heat resistance and improved physical properties. EA-40® is versatile and can be used for many different assembly and repair applications ranging from electrical potting to jewelry assembly to repairing plumbing fixtures. Bow makers have come to know EA-40® as a tremendous laminating resin. EA-40® provides highly moisture resistant bonds meeting the performance requirements for Federal Specification MMM-A-188, Type III.

Products

EA-40 epoxy lijm

  • EA-40 epoxy lijm /1,9kg

    EA-40 heldere epoxy lijm 2 comp. set 1,9kg

  • EA-40 epoxy lijm /7,3kg

    EA-40 heldere epoxy lijm 2 comp. set 7,3 kg

Instructions

Instructions
Safety - Use in a properly ventilated area (“room size” ventilation). Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk.

Store and use material at room temperature (73°F/23°C). This product has a limited shelf life and should be used as soon as possible.

A clean, dry surface is a necessary prerequisite for adhesive bonding. Adhesives will stick to either the surface of which a bond is desired or to that film of extraneous material directly on that surface. Rarely can a structural adhesive penetrate through surface contaminants to provide an optimum bond on an unclean surface.

Porous materials are simple to bond, provided they are dry. The surface should be sanded till clean and free from dust. Non-porous surfaces, such as found on metal and plastic materials, should be degreased, dried and roughened by sanding, sandblasting or chemical etching. The etched or sandblasted surfaces should be covered within a few hours of treatment to prevent contamination.

Handlers should wear clean cotton gloves to prevent body oils from contaminating the clean surfaces.

Epoxy adhesives do not perform well on metals such as nickel, chromium, tin or zinc nor on soft thermoplastics like polyethylene.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

MEASURING & MIXING - Measure equal amounts of Parts A and B (or 2A:1B) by volume into a clean mixing container. Mixing tools and containers should be clean and made of metal, glass or plastic. After dispensing required amount of Parts A and B into mixing container, mix thoroughly for 3 minutes making sure that you scrape the sides and bottom of the mixing container several times.

Application - Apply to prepared surface and let cure for 24 hours. Applying mild heat will cure EA-40® faster – 150°F/65°C for 6 hours.

Post Curing - After EA-40® has cured at room temperature, heating the epoxy to 150° F (65° C) for 4 to 8 hours will increase physical properties and performance. Let cool to room temp. before moving bonded substrates, machining, etc.

To Attain Maximum Heat Distortion Temperature - let cure for 24 hours at room temperature, heat cure for 2 hours at 250°F (122°C).

At mix ratio 1A:1B – HDT will be 163°F (73°C).

At mix ratio 2A:1B – HDT will be 217° F (103 °C)

Kieswijzer

Hier vindt u onze produkten gerangschikt naar diverse toepassingsmogelijkheden, zoals: Lifecasting, boetseren, afvormen, gieten, make-up, stuntwerk, dentaalwerk en studie.

  • Afvormen

    fllexibele materialen voor mallen: siliconen, pu-rubbers, alginaat etc.

  • Special Properties

  • Gietmaterialen

    Materialen voor het gieten van harde of flexibele objecten.

  • Schuimen

    Liquid Flexible Foam, Liquid Rigid Foam, Rigid Foam Blocks

  • Composieten

    Harsen, polyester, epoxy, acrylhars, glasvezels enz.

  • Cold Casting

    Metaalpoeders en plastics voor het "koud" gieten van IJzer, Brons, Messing of Tin.

  • Restauratie

    Voor het vervaardigen en herstellen van architectuur en ornamentiek.

  • Prototyping

    Materialen die worden gebruikt voor rapid prototyping

  • Textiel

  • Cosplay

    Producten om je eigen cosplay kostuums en rekwisieten te maken

FormX Newsletter Nieuwsbrief Over ons Contact Verkoopvoorwaarden Verzending we have vacancies FormX Academy Merken Toepassingen Is dit de baan voor jou?

Wij gebruiken cookies om onze website te optimaliseren en u de best mogelijke online ervaring te bieden. Door op "alles accepteren" te klikken gaat u hiermee akkoord. Geavanceerde instellingen