Habitat™ Fire Safe /1,91 kg

Free Form™ Habitat™ Fire Safe™ epoxyplamuur is een epoxy-sculptingplamuur met een hoge dichtheid en een vlambestendigheid (E84, klasse A).

Habitat™ Fire Safe™ is oplosmiddelvrij en bevat geen VOS.

De verwerkingstijd bedraagt 90 minuten en de uithardingstijd bedraagt 16 uur bij kamertemperatuur (23° C).

Epoxy hardt uit tot een zeer hard, vlam- en hittebestendig materiaal dat gemakkelijk overschilderbaar is.

Habitat™ Fire Safe™ bevat geen kankerverwekkende stoffen (kankerverwekkende stoffen).

Functies

Free Form™ Habitat™ Fire Safe™ is geschikt voor thematoepassingen binnen en buiten en voor algemeen beeldhouwen. Het is ook gecertificeerd als ‘aquariumveilig’ en wordt door aquaria en dierentuinen gebruikt om hyperrealistische bomen, wijnstokken, rotsen, koraal en andere weergave-elementen te maken.

Gebruiken met Habitat™ Vouwpoeder – vouw poeder in epoxyplamuur om het dikker te maken en doorzakken te verminderen wanneer het op een verticaal oppervlak wordt aangebracht. Folding Powder™ vermindert ook de plakkerigheid en maakt de epoxy beter hanteerbaar. Zodra de stopverf is aangebracht, kan deze worden gestempeld met een siliconenrubberstempel om herhalende patronen met ingewikkelde details over een groot oppervlak te creëren. Oppervlak kan worden gladgemaakt met alcohol of water. De nieuwe Habitat™ Fire Safe™ hecht zich zonder delaminatie aan uitgeharde Habitat™ Fire Safe™. Habitat™ Fire Safe™ smelt het schuim niet en kan worden gebruikt als EPS-schuimcoating. Free Form™ Habitat™ Fire Safe™ is tevens een uitstekend reparatiecement en hecht permanent aan zichzelf, PVC, Plexiglas™ (acryl), hout, vele metalen, kunststoffen en schuimsoorten.

Instructions

Safety – Use in a well-ventilated area (“room size” ventilation). Generally, if you use any epoxy system on a regular basis, wearing a NIOSH approved respirator is advised. Wear safety glasses, long sleeves and rubber gloves to minimize skin contact. Wear nitrile or vinyl gloves only.

Rate Of Coverage - Assuming a thickness of 6.3 mm, 454 g of Free Form™ Habitat™ Fire Safe™ will cover approximately 462 cm2.

Preparation – Materials should be stored and used at room temperature 23°C. This product has a limited shelf life and should be used as soon as possible. Mixing should be done in a well-ventilated area. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk.

Before mixing materials, apply Folding Powder to work surface in a 6.3 mm layer. Powder gloves with Folding Powder to eliminate sticking.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

Applying A Release Agent – For releasing epoxy from non-porous surfaces such as resin, metal, glass etc., use Ease Release™ 200 or 205 (available from Form X) to prevent adhesion.

Measuring - Free Form™ Habitat™ Fire Safe™ comes as two parts. Dispense equal amounts of Part A and Part B. These products have a limited shelf life and should be used as soon as possible.

Mixing - This product is mixed by hand. You must wear gloves when mixing this material, wearing vinyl gloves reduces inhibition risk. First, thoroughly coat gloves with folding powder to prevent sticking. Knead parts A+B together while folding powder into mixture. The amount of powder to add depends on desired working consistency. The more powder you add, the thicker the mixture becomes. Fold mixture into itself repeatedly until desired consistency is attained (3-5 minutes or a minimum of 20 folds)

Apply by gloved hand to horizontal, vertical or inverted surface. Important; pot life and cure time are reduced with elevated temperatures.

Stamp, Sculpt or Mold - Once in place, putty can be stamped using a rubber stamp (Rebound™ 25 silicone). Apply alcohol to stamp detail before using for precise detail and to keep stamp clean. Sculpt using gloved hands or tools. Putty can also be pressed into a silicone rubber mold to reproduce detail.

Smoothing Surface – Epoxy surface can be smoothed with water or isopropyl alcohol. Option: cover putty surface with clear plastic food wrap and smooth or sculpt with hand or tool. Leave wrap in place until material cures and remove. Cured surface will have a high gloss finish.

Curing and Heat Resistance – Habitat™ Fire Safe™ will cure in 16 hours at room temperature. Elevated heat will cure epoxy faster. At an ambient temperature of 60°C, the material will cure in as little as 30 minutes. A heat gun may also be used, as long as the surface temperature of the Habitat™ does not exceed 100°C. Putty cured at room temperature with a minimum thickness of 1.27 cm will resist temperatures up to 74°C.

Post Curing - For higher heat resistance, cured Habitat™ Fire Safe can be heat post-cured in a dedicated industrial oven. Cure at 80°C for two hours, followed by three hours at 100°C. Thin sections may need to be supported during post curing. Allow material to cool to room temperature before use.

Machining – Cured castings are rigid and durable. They resist moisture, moderate heat, solvents, dilute acids and can be machined, primed/painted or bonded to other surfaces (any release agent must be removed). If machining cured epoxy, wear dust mask or other apparatus to prevent inhalation of residual particles.

Painting – For outdoor display, cured Free Form™ Habitat™ Fire Safe™ can be primed and then painted with acrylic enamel paints. Let paint fully dry before putting part into service.

Removing Uncured Free Form™ Habitat™ Fire Safe - Remove as much uncured material from the surface as possible. Clean any residue with soap and water.

Optional - Use E-POX-EE KLEENER™ available from form x