Plasti Paste pasteuze hars

Plasti-Paste is een reukvrije, pasteuze, vezelversterkte, twee componenten hars die met kwast of spatel afdruipvrij op verticale oppervlakten aangebracht kan worden. De verwerkingstijd is 8-10 minuten. De ontvormtijd is ca. 90 minuten.

- geschikt voor sterke en lichtgewicht steunmallen.

- geschikt voor sterkte laag achter een gelcoat van Shell Shock

- geschikt voor vormgevingsdoeleinden

Technical bulletin Plasti-Paste


Plasti Paste Veiligheidsinformatie

- Lees het veiligheidsinformatie label. Klik op de afbeelding.

- Read the safety information label. Click on the image

- Lisez les informations de sécurité cliquez sur l'image

- Lea la etiqueta de información de seguridad. Haga clic en la imagen

- Lesen Sie das Sicherheitsinformationsetikett. Klicken Sie auf das Bild.



Plasti Paste producten

Plasti-Paste /1,5kg Shore 70D | Uithardtijd: 90min 60,51 EUR



Plasti-Paste /5kg Shore D70 | Uithardtijd: 90min 162,18 EUR



Plasti-Paste /26kg Shore 70D | Uithardtijd: 90min 646,49 EUR





Benodigdheden

Mengbekers
Maatcylinders & bekers
Weegapparatuur
Kwasten
Veiligheidsmaterialen
Losmiddellen




Mengen, Meten & Wegen

maatbeker 30ml Measuring cup 30ml + graduation 0,19 EUR



maatbeker 125 ML Measuring cup 125 ML + Graduation 0,48 EUR



Mixing Beaker rond / 500cc 500 cc contents 0,25 EUR



Mixing Beaker rond /1000cc plastic mixing beaker 1162 ml 0,64 EUR



Mengbeker Smooth-On / 473ml Mengbeker Smooth-On / 16oz 1,04 EUR



mengbeker Smooth-On / 946ml mengbeker Smooth-On / 32oz 1,09 EUR



mengbeker Smooth-On / 1892ml mengbeker Smooth-On / 64oz 2,84 EUR



mengbeker Smooth-Onr / 4880ml mengbeker Smooth-Onr / 165oz 3,35 EUR



Mengbeker Colad met maatregistratie / 350ml 0,57 EUR



Mengbeker Colad Met maatregistratie / 700ml 0,63 EUR



Mengbeker Colad met maatregistratie / 1400ml Mengbeker Colad met maatregistratie / 1400ml 0,80 EUR



Mengbeker Colad Met maatregistratie / 2300ml 1,46 EUR



Flexibele Mengbeker - 500 ml Voor gips en alginaat 8,05 EUR



Flexibele Mengbeker - 1750 ml Voor gips en alginaat 19,34 EUR



Tongspatels voor medisch En niet medisch gebruik 3,42 EUR



roerhoutje, klein - 220x17x3 mm roerhoutje, klein - 220x17x3 mm 0,05 EUR



roerhoutje, groot - 300x20x4 mm roerhoutje, groot - 300x20x4 mm 0,24 EUR



Tristar weegschaal KW2430 Digitale keukenweegschaal. Weegt tot 2kg op 1 gram nauwkeurig. Excl. batterij. 20,21 EUR



injectiespuit 50 cc met catheterpunt injectiespuit 50 cc met catheterpunt 5,76 EUR



Colad Turbomix /per 200 200 stirrers in dispenser. 61,38 EUR



Turbine Mixer Turbine Mixer 16,11 EUR



mengbak vierkant wit /2000ml Square mixing Bowl white 180x180 mm; 2000 cc 0,91 EUR





Preparation – Materials should be stored and used in at room temperature 23° C. This product has a limited shelf life and should be used as soon as possible. Mixing should be done in a wellventilated area. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. If making a 2 or more piece mother mold, apply appropriate shim apparatus to rubber mold exterior.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

Applying A Release Agent – This product is adhesive and will bond to many surfaces. A sealer followed by a release agent is necessary to facilitate demolding when applying as a mother mold over a cured mold rubber. Use Sonite™ Wax followed by a coating of Universal™ Mold Release or Ease Release 200 release agent. A liberal coat of release agent should be applied onto all surfaces that will contact the plastic. You can also apply aluminum foil as a barrier over the surface followed by an application of Mold Release agent.

PRE-MIX Part B Before You Start – Part B is a thick paste containing oil that needs to be pre-mixed before being dispensed into measuring container. Dig deep to re-disperse oil & paste components that may have separated.

Measuring – The components of Plasti-Paste™ requires two different sized containers. The first will be used for measuring out amounts of Part A and Part B. The second should be large enough to contain both components and allow thorough mixing. IMPORTANT: Shelf life of Part A (Yellow Container) is reduced after opening. Remaining product should be used as soon as possible. XTEND-IT™ Dry Gas Blanket will prolong shelf life of unused liquid urethanes.

Mixing – Mix Ratio is 1A:3B by volume (41A:100B by weight). (Step 1) Fill measuring container to the top with Part B paste, making sure to eliminate any air voids. Level off the top of the container and remove any excess material. The paste should then be thoroughly emptied into a larger container that will act as your mixing container. Repeat As Necessary. (Step 2) Fill the measuring container to the top with Part A liquid and empty into mixing container. Mix thoroughly for 2-3 minutes making sure that you scrape the sides and bottom of the mixing container several times. Eliminate color streaks. If adding So-Strong™ color tints, pre-mix color with the Part B before adding Part A.

Mixing Large Batches - A ‘Turbine’ mechanical mixer attached to a power drill will make mixing large batches of material much easier.

IMPORTANT: Shelf life of product is reduced after opening. Remaining product should be used as soon as possible. Immediately replacing the lids on both containers after dispensing product will help prolong the shelf life of the unused product. XTEND-IT™ Dry Gas Blanket (available from form X) will significantly prolong the shelf life of unused liquid urethane products.

Applying – Mixed material thickens quickly and pot life is limited. Do not delay between mixing and applying. To increase working time, spread entire container contents over rubber mold surface and cover and spread mixture to uncovered areas. Apply uniformly with spatula over mold surface. Material will adhere to itself if additional layers are needed. Apply at least 1 cm thickness, making sure rubber mold is thoroughly covered. For maximum strength and heat resistance, 1.27 cm thickness is recommended. Large molds may require added thickness for support shell stability. Supports (wood or metal) may be embedded for added stability and handling. Prevent a jagged surface; Final layer of Plasti-Paste™ can be smoothed by wiping solvent (denatured alcohol or acetone) onto surface with gloved hand.

Making A Two Piece Shell – Plasti-Paste™ will bond to most surfaces and itself tenaciously. A barrier coat of paste wax followed by Universal™ Mold Release applied to all surfaces is necessary to prevent adhesion. Applying aluminum foil to the contours of all surfaces followed by Universal™ Mold Release will also prevent adhesion.

Curing – Plastic will be hot immediately following cure. Let cool to room temperature before handling. Material will develop handling strength and can be handled in about 90 minutes depending on mass. At this point, it is stable enough to demold, re-assemble over rubber mold and make a casting (hold 2 or more piece assemblies together with elastic bands, mold straps or bolts). Large sections should be bolted together to minimize distortion. Full strength develops in 24 hours.

Heat Resistance – Fully cured plastic with a minimum thickness of (1.27 cm) will resist temperatures up to 55°C. To improve heat resistance to 70°C, post cure material at 65°C for 16 hours.

If machining or sanding cured plastic, wear NIOSH approved mask to prevent inhalation of residual particles.

Storage – For best storage results, cast into rubber mold with a gypsum plaster or other dimensionally stable material, assemble mold inside the Plasti-Paste™ support shell and store assembled molds on a level surface indoors at room temperature in a dry place.



Kwasten

flat brush 30mm platte wegwerpkwast 0,80 EUR



flat brush 40mm platte wegwerpkwast 0,92 EUR



flat brush 50mm platte wegwerpkwast 1,39 EUR



flat brush 60mm platte wegwerpkwast 1,38 EUR



flat brush 70mm platte wegwerpkwast 1,39 EUR



Calupaint Platte Calupaint Platte 2,60 EUR



polyesterkwast 20mm polyester brush 20mm round 3,09 EUR



polyesterkwast 25mm polyester brush 25mm round 3,51 EUR



houten polyesterkwast 35mm houten polyesterkwast 35mm plat 2,21 EUR



houten polyesterkwast 50mm plat wooden polyester brush 50mm flat 3,46 EUR



Polyester kwast plat 75mm Polyester brush, Flat, 75 mm 3,33 EUR



kwast plat 40mm Brush, flat, 40mm, wooden handle. 2,84 EUR





Bescherming

Stenchmask carbon fibre Stenchmask carbon fibre 5,41 EUR



Filter ABEK1 for 3M 6200 maskers Protection against chemicals vapors 36,87 EUR



Paint spray mask Colad Easy to wear paint spray mask. 35,39 EUR



3M 06941 Halfgelaatmaske FFA1P2D 50,53 EUR



Protective Glove Nitrile S Protective Glove Nitrile Small 11,01 EUR



Protective Glove Nitrile L Protective Glove Nitrile Large 11,01 EUR



Protective Glove Nitrile XL Protective Glove Nitrile Extra Large 11,01 EUR



Protective Glove Nitrile M Protective Glove Nitrile Medium 11,01 EUR



3M safety glasses Classic 3M safety glasses Classic 15,19 EUR





Losmiddelen

Spray

Safety Info Universal Mold release



Ease Release™ 200 / 400gr Ease Release™ 200 / 400gr 19,54 EUR



Ease Release™ 300 / 400gr Ease Release™ 300 / 400gr 18,22 EUR



Ease Release™ 400 / 400gr Ease Release™ 400 / 400gr 21,33 EUR



Spray

Safety Info Ease Release Group



Ease Release™500 / 400gr Ease Release™500 / 400gr 22,30 EUR



Acmos 82 aerosol / 400gr Afwasbare universeel lossingsmiddel / was in aerosol spuitbus 20,63 EUR



Spray

Safety Info Acmos



Universal Mold Release aerosol / 400gr Op Silicone gebaseerde Universal lossingsmiddel - aerosol spuitbus 400 gr 17,05 EUR



Kwikee Sprayer - 946 ml Pressure Sprayer The Kwikee sprayer is an economical alternative to aerosols for dispensing release agents and sealing agents. It is a faster, labor-saving way to cover large models or molds and delivers sealing a... 138,57 EUR





(C) 2009 - Alle rechten voorbehouden

Deze pagina afdrukken